Download Article

Download Article

If you're van is throwing the code "Intake Manifold Runner Control Valve stuck open", this article will show you the easy, yet still correct, way to replace it. Just follow the steps below carefully, and keep common sense in mind, and you'll do great. See tips below for a tool list.

Steps Download Article

  1. 1

    Find out the problem. First (most important step) is the diagnosis. Don't skip this step as you might replace something that isn't broken. There may not even be a problem with your valves (i.e. the vacuum isn't even reaching them to be able to shut them). These valves, if good, should close with very little vacuum, and should also hold the vacuum when applied with a vacuum pump. The default position (engine off, no vacuum) for these valves is open. Once the engine is started (and vacuum is being applied) these valves will close until wide open throttle, when vacuum is absent.

  2. 2

    Disconnect the negative terminal at the battery. DO NOT skip this step under any circumstances. If you want to know the why, there is plenty of literature out there and plenty of reasons, the best being YOUR SAFETY. Once it's removed, secure it somewhere that you are sure it won't come into contact with the terminal again unintentionally (picture).

    Advertisement

  3. 3

    Remove the accessory belt by relieving the tension on the belt. Good luck trying to get a socket on this beast. I'm sure they have a nice shiny tool that makes this easier, but I used the box end of a wrench to get on this. Pull the wrench toward the front of the vehicle until enough tension is off the belt to remove it from the alternator pulley. Doing this with a wrench does require a good bit of strength. If you can't get it to move, or don't think you would be able to put enough power behind it to get it to turn, talk to one of your local parts store to see if you can get your hands on that tool. They may even have it on a loaner program so you wouldn't actually have to buy one.

  4. 4

    Remove black dust boot from the top of the alternator (just wiggle it back off where it is). Take off the nut hiding under there, and lay the wire to the side. Thread this nut back in place once you have the wire off so it doesn't get lost somewhere.

  5. 5

    Remove the three bolts holding the alternator to the accessory bracket and the electrical connector on the side of the alternator. The connector was already taken out in this picture, but top arrow pointing to the right is where it was. And just in case you're curious, there's a picture here that shows what it looks like without the alternator in there.

  6. 6

    Take the vacuum lines off of the fuel pressure regulator, and both of the Intake Manifold Runner Control (IMRC) Valves. Now, swing the whole harness out of the way. Remove the electrical connector on the front valve. Just squeeze the connector at the back (where the arrow is on the picture with the connector off) and pull away from the valve.

  7. 7

    Remove the white clip from the arm of the valve. You won't be reusing this clip, as a new one should come with your new valve. Remove the two bolts holding the valve onto the engine. This is a little tricky, and where the u-joint comes into play.

  8. 8

    Be careful. The lines for the power steering fluid run right where you need your wrench to go, so be VERY careful not to bend these lines too much, or even break them or you may be making an additional repair! Again, if you're curious, see the added picture with the valve out.

  9. 9

    Get the white clip for the new valve, and insert it in the hole that the old one came out of. Insert the arm of the new valve into the clip, and insert the two bolts that hold it on.

  10. 10

    Put everything back on that you took off! Start with the electrical connector for the IMRC Valve, then the alternator, then the vacuum lines for the valves and fuel pressure regulator, and finally, the accessory drive belt. Just follow all of these steps in reverse, and you'll be taking it for a test drive in no time!

  11. 11

    Do a second check to make sure that you have everything back together that you took apart, and that all of your tools are out of the engine compartment. Start up the vehicle, and verify that both valves are now closed. Having an assistant available to start the vehicle while you watch the valves could be helpful, but it will be an obvious change from open to closed. Once that your are satisfied that both valves are closing when you turn the vehicle on, close the hood and take it for a test drive and feel the difference!

    Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

  • If you don't disconnect the negative terminal from the battery, there is a chance of electrical shock and/or electrical component damage (any electrical device in the vehicle).

Advertisement

Things You'll Need

  • Wrench with socket set 1/4, 3/8, and 1⁄2 inch (1.3 cm) drive (most socket sets, even the most basic, will have all the sockets necessary for this repair) The only thing you may need the 1/2 drive wrench or breaker bar for are the alternator bolts. They're on there relatively snug.
  • 1⁄4 or 3⁄8 inch (0.6 or 1.0 cm) drive u-joint
  • Flat head screwdriver
  • A tool for the belt tensioner would be helpful, but not 100% necessary
  • Open end/box wrench (I believe it was a 5/8) for the belt tensioner. The longer, the better.
  • IMRC Valve

About This Article

Thanks to all authors for creating a page that has been read 34,981 times.

Did this article help you?